(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/310762719_174097598533869_2015889089625884380_nlow.jpg)How to Replace a Kia Sportage Replacement Key
(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/308785165_499195788347328_5859105632268553197_nlow.jpg)For many kia car key replacement models the key comes with the keyless entry system that is built into the key. This key is similar to remote controls and can be exchanged by a Kia dealer.
Key fobs can stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signal interference or water damage. Here are some helpful tips on how you can get your Kia Sportage replacement key back to working.
How do you replace a remote key or smartkey
No matter if your kia keys replacement is equipped with an intelligent key, remote key push to start key or a regular non-transponder metal key, the battery in these keys will eventually need replacing. This is especially in the event that your car displays a message that the smart key or remote has a low battery.
This is a relatively simple procedure. To replace the battery in the keyfob take out your mechanical key from the slot at the back of the fob. Then, pry the cover off. Inside the key fob, there will be tiny screws that hold the battery in its place. Remove the old battery by removing the screw using a small screwdriver. Insert the new battery and then close the gap on the key fob.
Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're set! You can now use your Kia's hands-free lock/unlock feature when your fingers are cold or you have to go on errands around Brandon.
Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a programing machine that is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, you will need to be aware of the key code printed on the key code tag and keep it in a secure location.
How do you replace a battery?
If the Kia key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is low. A weak battery could cause other issues, like the check engine light flashing or the engine not turning properly. It is quite simple to replace key fob batteries using just the use of a few tools.
Before you begin the process be sure that your vehicle is off and that all doors are shut. Find the small metal or plastic piece on the bottom of your key fob and move it until a metal key slides out. The key can be put into the door's driver handle to unlock your car.
To replace the key fob's battery, take off the cover at the rear and use a plier bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then place the new battery so that its “+” side faces you, and the “-” negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.
Once the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition for a few times until the door locks. Then, test your kia remote key fob key fob to determine whether it's functioning properly again.
How do I replace a smart keys
Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key has an embedded mechanical key blade, however, the standard key fob does not. Both kinds of key fobs contain batteries that will eventually have to be replaced. Fortunately, this is an easy process that only takes about two minutes.
Before you get started, you will want to make sure that you are on a level surface with sufficient lighting and that your Kia is not on. Also, keep in mind that there are tiny pieces inside the fob that could be removed if not cautious.
The first step is to locate the small release button on the lower backside of the fob. It could be an oval or circular slot. You can open the key fob by pressing the button.
Once you have the key fob open it is easy to remove the old battery and replace it. The new battery is the CR-2032, and it can be purchased online or in your local auto parts shop. After installation you should be able to lock, unlock and start your vehicle using your key fob even if the engine isn't running!
How to replace the mechanical key?
The Kia keyfob is a great convenience, allowing us to lock or unlock our car with just pressing a button. Like all devices it is possible that the Kia key fob may have issues. Luckily, there are ways to troubleshoot these issues and keep our key fobs in good working order for the long run.
One of the most frequent problems is a dead or dead battery. The battery could cause the device to stop working or operate intermittently. If this is the problem, replace the battery with a new one.
If this isn't enough to solve the problem, use an ordinary screwdriver with a flat head to wedge the fob's plastic casing open. Be sure not to damage any internal components, or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new battery.
Once the new battery is in, close and open the doors with the mechanical key (every kia rio key fob fob has an emergency mechanical key that can fit in the slot). Test the key fob to confirm it's working as intended. If the fob isn't working, contact an authorized locksmith or dealer to help solve the problem. Make sure they make you an emergency key that works across all trunk and door cylinders in order to avoid lockouts in the future.