How to Replace a kia sorento key Sportage Replacement Key
The key of a lot of Kia models has a keyless entry system built in. This key typically resembles the remote control and can be exchanged with a fresh one from a Kia dealer or locksmith.
Key fobs are prone to malfunction due to various reasons, such as a dead coin battery, worn buttons signal interference, water damage and a damaged receiver module. Here are some suggestions on how to get your Kia Sportage replacement key to function again.
How to replace the remote key or smart key
The battery in your Kia's intelligent key will eventually have to be replaced, whether it's a remote or a push-to-start one, or a regular metal key that is not equipped with a transponder. This is especially relevant if your car displays a message indicating that the remote or smart key is not powered by the battery.
This is a relatively easy process. To replace the battery in the key fob take the mechanical key from the slit in the back of the key fob and pry open the cover. Inside the key fob there will be a small screw that holds the battery in the correct position. Remove the old battery by removing the screw using a small screwdriver. Insert the new battery and then close the opening on the key fob.
Test the key fob by pressing the lock and unlock buttons. If the doors lock and unlock exactly as you expect, then you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to go on errands around Brandon.
Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys) are not required for programming. If your keys need to be reprogrammed, you must be aware of the key code stamped on the tag that identifies the key and save it in a safe place.
How do I replace the battery?
If your kia picanto key fob replacement key fob isn't responding when you press the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A weak battery could cause other issues, such as the check engine light flashing or the engine not working correctly. Fortunately, replacing the battery on the key fob is a simple DIY task that requires only the most basic tools.
Make sure that you shut off your vehicle and shut all doors before you begin. Locate the small metal or plastic piece at the bottom of your key fob, and jiggle it until a metal key pops out. This key can be inserted into the driver door handle to unlock your car.
To replace the battery on the key fob, remove the cover at the rear. Utilize a plastic plier tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the new battery to ensure that the “+” positive side faces your face and the “-” negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the contacts made of metal.
Once the new battery is installed after which you turn the key fob off and back on in the ignition several times until the door locks. You can then test the kia key copy's Key fob again to confirm that it's working as intended.
How do I replace a smart key
Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade however, the standard key fob does not. Both key fobs have batteries that will eventually require changing. This is an easy process which takes just two minutes.
Before you start it is important to ensure that you are on a flat surface with enough lighting and that your Kia is not on. Keep in mind that there are tiny pieces inside the fob which could fall out if you are not cautious.
(Image: https://www.thekeylab.co.uk/wp-content/uploads/sb-instagram-feed-images/311135906_1281855972636056_2987376612771239945_nlow.jpg)The small release button is located on the lower backside. It could be a circular button or a rectangular slot. You can open the key fob by pressing the button.
Once the key fob is open, remove the battery that was in it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. Once you're done with the battery, you should be able to lock or unlock your car using your key fob, even if the engine isn't running!
How do you replace a mechanical key
The Kia keyfob is a great convenience, allowing us to lock or unlock our car simply by pressing the button. However, like all devices there are issues with it from time to time. There are solutions to resolve these issues and keep your key fobs working for an extended period of time.
A low or dead battery is one of the most common problems. This can cause your fob to stop working or work intermittently. If this happens you should replace the battery with a fresh new one.
If this isn't enough to solve the issue, try using a standard flathead screwdriver to push the fob's plastic casing open. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the old battery and replace it with a brand new one.
Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to confirm it's working as intended. Contact a dealer or a locksmith to solve the issue in the event that the key fob is not working. Make sure they make you an emergency key that works across all door and trunk cylinders to avoid lockouts again.