[[//www.youtube.com/embed/https://www.youtube.com/watch?v=Ha7bnPiDd-w/hq720.jpg?sqp=-oaymwEcCOgCEMoBSFXyq4qpAw4IARUAAIhCGAFwAcABBg==\u0026rs=AOn4CLDOcg7zK0-RF0X0ipVgNhq6D-0HAw|external page]]Trusted pros are available for same-day installation when you call before noon in most areas. When the electrical connections are made and all access plates are reinstalled, restore power by turning the circuit breaker back on.(Image: [[https://inspectapedia.com/plumbing/Rheem-RTREX13-Heater-0122-DJFc.jpg|https://inspectapedia.com/plumbing/Rheem-RTREX13-Heater-0122-DJFc.jpg]]) Tankless water heaters are available in select markets only. To find out more, submit the form above or visit your local Lowe’s to speak with a project specialist and see which units are available in your area. A thermal expansion tank alleviates excess pressure in the lines of a closed system.
Make certain to install a sediment trap to  prevent dirt from entering the gas burner. Use flexible lines so as not to put undue strain on the water heater components. If your water pressure exceeds 80 psi, install a pressure-reducing valve. If you’re using a gas or propane water heater, you must make allowance for the vent line and ensure you comply with vent termination clearance requirements. They use a gas burner or electricity to heat the water pipe, supplying water on demand but often at a slower flow rate.
If blocks cover the studs, use a masonry bit to create a pilot hole. Wrap the strap around the water heater and adjust the size, securing the adjustable bracket on the opposite side. Pull the strap tight and repeat the process on the lower strap. Seismic straps should be installed approximately 6 inches from the top of the water heater and 18 inches from the bottom.
Like hot water storage tanks, tankless units can be stored in a basement or utility closet. They’re smaller than a tank unit, so they can also be mounted to a bathroom or bedroom wall. If you notice any leaks, immediately turn off the water supply and tighten the connections further. Turning off the water supply will prevent any additional water from entering the tank while you drain it. Professional installers have all the necessary tools and equipment. They come prepared with sealing and insulation for your unit, which minimizes heat loss and saves energy.
All these tasks require the knowledge and experience of licensed professionals. Additionally, the water heater unit itself is a significant investment, with high-quality, energy-efficient models leading to higher prices. In some areas, rebates are available for high-efficiency water heaters. If the piping has been soldered into place, use a tubing cutter to cut the pipe. Clean the pipe with Emery cloth before cutting the pipe. This will make it easier to prep for the solder connection later.
Use two wrenches to reduce the stress on the gas valve, keeping one on the valve itself to steady it and one to do the turning. Use a pipe wrench to get the  temperature and pressure relief valve fully tightened. Before starting work, check that you have the tools and materials you need.
If you’re not in an earthquake zone, skip ahead to the next step. Some areas require dielectric fittings to reduce corrosion between two different metals. Your area’s local codes and ordinances should detail the specifics of installation in your area.
Clean the inside of each joint and the end of each section of pipe. Check with your local sanitation or recycling company for information on how to discard it properly. When using a professional installer, make sure they remove the old water heater as part of their service. Measure the distance from the top of the water heater to the hot and cold water lines. Remove the cover of the heater and connect the electric wires to your grid.
Refer to the manufacturer’s instructions for installing a thermostatic mixing valve. Defer to the manufacturer’s instructions for seismic strap installation. Before you buy, note the stem length required by your water heater model. Install the water heater in an area that leaves at least 6 inches of clearance around it for ventilation.
Remove any remaining unions with a pipe wrench or tubing cutter. Unscrew and disconnect the vent shaft at the top of the heater. Attach a hose to the drainage pipe and let the water flow into a drain. The water heating capacity is determined by the total wattage of the elements.  For more information on silzeropodcast.com have a look at our own page. These vary from 12.2 kW up to 32 kW, depending on the output capacity of the water heater. The Leadership in Energy and Environmental Design program is a method for rating green buildings.(Image: [[https://s3-us-west-2.amazonaws.com/partners-dashboard/wp-content/uploads/sites/41/20190508115802/40GallonElectric2.jpeg|https://s3-us-west-2.amazonaws.com/partners-dashboard/wp-content/uploads/sites/41/20190508115802/40GallonElectric2.jpeg]])